Omega Cal. 611 Tech sheet

Home Forums General Discussion Forum Omega Cal. 611 Tech sheet

  • This topic is empty.
Viewing 8 posts - 1 through 8 (of 8 total)
  • Author
    Posts
  • #50107
    johnno
    Participant
    • Topics Started: 19
    • Total Posts: 55

    Hi

    Anyone any idea where I might track down a tech sheet for an Omega 611 movement?

    thanks in advance :)

    John

    #64971
    johnno
    Participant
    • Topics Started: 19
    • Total Posts: 55

    To be specific I am looking for an oiling guide for this particular movement or similar.

    #64972
    Bob Tascione
    Moderator
    • Topics Started: 38
    • Total Posts: 1553

    Hi John,
    I remembered an earlier post from member Chaplin37 looking for the same 600 series info that you’ve requested.
    Dug up the post but not sure it’s going to be of much help. Worth a look though (I’ll post link below). I’ve never been able to locate an oiling chart for that movement and would also like to have one as Omega watches produced during that era is of interest to me.
    Here’s the link: https://www.clockrepairtips.com/forum/viewtopic.php?f=2&t=1893
    If you do run across a pdf chart for the 611 (or any 600s) please post it up here John.
    Thanks,
    Bob

    #64973
    johnno
    Participant
    • Topics Started: 19
    • Total Posts: 55

    Thanks, Bob. Very much appreciated!
    I will certainly post here as soon/if I can find one.
    cheers
    John

    #64974
    johnno
    Participant
    • Topics Started: 19
    • Total Posts: 55

    Hi Bob

    I found this site which covers a variety of movements. Certainly a number of 600 series but unfortunately no oiling guides and not as detailed as I would have hoped for. However, getting there. It’s a start!

    http://tech.gleaveandco.com/home

    cheers
    John

    #64975
    johnno
    Participant
    • Topics Started: 19
    • Total Posts: 55
    #64976
    randy
    Participant
    • Topics Started: 39
    • Total Posts: 594

    Johnno
    I can’t find one specifically for the 611…but DR Ranfft’s webpage lists the following as movements in the same family.
    My guess is that you might get lucky and find a lubrication chart for one of them that could be applied to all the movements.
    Maybe start with the 600 ??

    manual wind:
    600: Reed’s regulator
    601: excenter regulator
    602: excenter regulator, chronometer
    610: Reed’s regulator, date
    611: excenter regulator, date
    613: excenter regulator, quickset date

    Hope this helps somehow !

    Randy

    #64977
    randy
    Participant
    • Topics Started: 39
    • Total Posts: 594

    OK…I think I found something really close ???

    Go here 1st
    https://www.cousinsuk.com/document/search/0?SearchString=omega+611+lubrication

    In that PDF…you’ll find a note that says to see working instruction 44

    At the bottom of that page, you’ll see this :
    Omega Working Instruction 40: Rules for Lubrication (1334KB)

    Download it, as it shows a ton of lubrication specs in detail

    That said …I’m still trying to find “44”

    The AWCI also has an older file..if you are a member.
    It may show more info
    https://www.awci.com/member-center/technical-guides-references/omega-working-instructions/

Viewing 8 posts - 1 through 8 (of 8 total)
  • You must be logged in to reply to this topic.
johnnoOmega Cal. 611 Tech sheet